diff --git a/README.md b/README.md
new file mode 100644
index 0000000..4a34871
--- /dev/null
+++ b/README.md
@@ -0,0 +1,126 @@
+# ESP32CAM-RTSP
+
+Simple [RTSP](https://en.wikipedia.org/wiki/Real_Time_Streaming_Protocol) server.
+Easy configuration through the web interface. Stable.
+
+Flashing this software on a esp32cam module will make it a **RTSP streaming camera** server.
+This allows CCTV systems and applications like  **VLC** to connect directly to the ESP32CAM camera stream.
+The RTSP protocol also allows to stream directly to a server using **ffmpeg**.
+This makes the module a camera server allowing **recording** and  so the stream can be **stored on a disk** and replayed later.
+
+This software supports the following ESP32-CAM modules:
+- ESP32CAM
+- AI THINKER
+- TTGO T-CAM
+
+![ESP32CAM module](assets/ESP32-CAM.jpg)
+
+This software provides a **configuration web server**, that can be used to:
+- Set the WiFi parameters,
+- Set the timeout for connecting to the Access point,
+- Set an access password,
+- Select the board type,
+- Select the image size,
+- Select the frame rate,
+- Select the JPEG quality
+
+The software provides contains also a mDNS server to be easily discoverable on the local network.
+
+## Required
+
+- ESP32-CAM module
+- USB to Serial (TTL level) converter or the piggyback board ESP32-CAM-MB
+- [**PlatformIO**](https://platformio.org/) software (free download)
+
+## Installing and running PlatformIO
+More information can be found at: [https://docs.platformio.org/en/latest/installation.html](https://docs.platformio.org/en/latest/installation.html) below the basics.
+
+### Debian based systems command-line
+Install platformIO
+```
+ sudo apt-get install python-pip
+ sudo pip install platformio
+ pio upgrade
+```
+
+### Windows / Linux and Mac
+Install [**Visual Studio code**](https://code.visualstudio.com) and install the PlatformIO plugin.
+For command line usage Python and PlatformIO-Core is sufficient.
+
+## Putting the ESP32-CAM in download mode
+
+### ESP32-CAM-MB
+When using the ESP32-CAM-MB board, press and hold the GP0 button on the ESP32-CAM-MB board.
+Then press short the reset button (on the inside) on the ESP32-CAM board and release the GP0 button.
+This will put the ESP32-CAM board in download mode.
+
+### FTDI adapter
+When using an FTDI adapter, make sure the adapter is set to 3.3 volt before connecting. Use the wiring schema below.
+![ESP FTDI wiring](assets/ESP32CAM-to-FTDI.png)
+
+After programming remove the wire to tge GPIO00 pin to exit the download mode.
+
+## Compiling the software
+
+Open a command line or terminal window and clone this repository from GitHub.
+
+```
+git clone https://github.com/rzeldent/esp32cam-rtsp.git
+```
+go into the folder
+```
+cd esp32cam-rtsp
+```
+
+Next, the software has to be compiled. Type:
+```
+ pio run
+```
+
+When finished, make sure the ESP32-CAM is in download mode (see previous section) and type:
+```
+ pio run -t upload
+```
+
+When done remove the jumper when using a FTDI adapter or press the reset button on the ESP32-CAM.
+To monitor the output, start a terminal using:
+```
+ pio device monitor
+```
+
+## Setting up the ESP32CAM-RTSP
+After the programming of the ESP32, there is no configuration present. This needs to be added.
+To connect initially to the device open the WiFi connections and select the WiFi network / accesspoint called **ESP32CAM-RTSP**.
+Initially there is no password present.
+
+After connecting, the browser should automatically open the status page.
+In case this does not happens automatically, connect to [http://192.168.4.1](http://192.168.4.1).
+This page will display the current settings and status. On the bottom, there is a link to the config. Click on this link.
+
+This link brings up the configuration screen.
+
+![Configuration screen](assets/Configuration.png)
+
+Configure at least:
+- The WiFi network settings. No dropdown is present to show available networks! Enter the Access point name manually.
+- A password for accessing the Access point (AP) when starting. (required)
+- the type of the ESP32-CAM board
+
+When finished press Apply to save the configuration. The screen will redirect to the status screen.
+Here it is possible to reboot the device so the settings take effect.
+It is also possible to restart manually by pressing the reset button. 
+
+## Connecting to the RTSP stream
+RTSP stream is available at: [rtsp://esp32cam-rtsp.local:554/mjpeg/1](rtsp://esp32cam-rtsp.local:554/mjpeg/1).
+This link can be opened with for example [VLC](https://www.videolan.org/vlc/).
+
+**Please be aware that there is no password present on the stream!**
+
+## Connecting to the configuration
+When a connection is made to [http://esp32cam-rtsp](http://esp32cam-rtsp) the status screen is shown.
+Clicking on the configuration link will open the configuration. It is possible that a password dialog is shown.
+For the user enter 'admin' and for the password the value that has been configured as the Access point password.
+
+## Credits
+esp32cam-ready depends on PlatformIO and Micro-RTSP by Kevin Hester.
+
diff --git a/assets/Configuration.png b/assets/Configuration.png
new file mode 100644
index 0000000..ccef624
Binary files /dev/null and b/assets/Configuration.png differ
diff --git a/assets/ESP32-CAM-MB.jpg b/assets/ESP32-CAM-MB.jpg
new file mode 100644
index 0000000..13226eb
Binary files /dev/null and b/assets/ESP32-CAM-MB.jpg differ
diff --git a/assets/ESP32-CAM.jpg b/assets/ESP32-CAM.jpg
new file mode 100644
index 0000000..e69fe5f
Binary files /dev/null and b/assets/ESP32-CAM.jpg differ
diff --git a/assets/ESP32CAM-to-FTDI.png b/assets/ESP32CAM-to-FTDI.png
new file mode 100644
index 0000000..6cb016d
Binary files /dev/null and b/assets/ESP32CAM-to-FTDI.png differ